-h

Display a brief usage overview.

-V

Displays the version of Suricata.

-c <path>

Path to configuration file.

-T

Test configuration.

-v

Increase the verbosity of the Suricata application logging by increasing the log level from the default. This option can be passed multiple times to further increase the verbosity.

This option will not decrease the log level set in the configuration file if it is already more verbose than the level requested with this option.

-r <path>

Run in pcap offline mode (replay mode) reading files from pcap file. If <path> specifies a directory, all files in that directory will be processed in order of modified time maintaining flow state between files.

--pcap-file-continuous

Used with the -r option to indicate that the mode should stay alive until interrupted. This is useful with directories to add new files and not reset flow state between files.

--pcap-file-recursive

Used with the -r option when the path provided is a directory. This option enables recursive traversal into subdirectories to a maximum depth of 255. This option cannot be combined with –pcap-file-continuous. Symlinks are ignored.

--pcap-file-delete

Used with the -r option to indicate that the mode should delete pcap files after they have been processed. This is useful with pcap-file-continuous to continuously feed files to a directory and have them cleaned up when done. If this option is not set, pcap files will not be deleted after processing.

-i <interface>

After the -i option you can enter the interface card you would like to use to sniff packets from. This option will try to use the best capture method available. Can be used several times to sniff packets from several interfaces.

--pcap[=<device>]

Run in PCAP mode. If no device is provided the interfaces provided in the pcap section of the configuration file will be used.

--af-packet[=<device>]

Enable capture of packet using AF_PACKET on Linux. If no device is supplied, the list of devices from the af-packet section in the yaml is used.

-q <queue id>

Run inline of the NFQUEUE queue ID provided. May be provided multiple times.

-s <filename.rules>

With the -s option you can set a file with signatures, which will be loaded together with the rules set in the yaml.

-S <filename.rules>

With the -S option you can set a file with signatures, which will be loaded exclusively, regardless of the rules set in the yaml.

-l <directory>

With the -l option you can set the default log directory. If you already have the default-log-dir set in yaml, it will not be used by Suricata if you use the -l option. It will use the log dir that is set with the -l option. If you do not set a directory with the -l option, Suricata will use the directory that is set in yaml.

-D

Normally if you run Suricata on your console, it keeps your console occupied. You can not use it for other purposes, and when you close the window, Suricata stops running. If you run Suricata as daemon (using the -D option), it runs at the background and you will be able to use the console for other tasks without disturbing the engine running.

--runmode <runmode>

With the –runmode option you can set the runmode that you would like to use. This command line option can override the yaml runmode option.

Runmodes are: workers, autofp and single.

For more information about runmodes see Runmodes in the user guide.

-F <bpf filter file>

Use BPF filter from file.

-k [all|none]

Force (all) the checksum check or disable (none) all checksum checks.

--user=<user>

Set the process user after initialization. Overrides the user provided in the run-as section of the configuration file.

--group=<group>

Set the process group to group after initialization. Overrides the group provided in the run-as section of the configuration file.

--pidfile <file>

Write the process ID to file. Overrides the pid-file option in the configuration file and forces the file to be written when not running as a daemon.

--init-errors-fatal

Exit with a failure when errors are encountered loading signatures.

--strict-rule-keywords[=all|<keyword>|<keywords(csv)]

Applies to: classtype, reference and app-layer-event.

By default missing reference or classtype values are warnings and not errors. Additionally, loading outdated app-layer-event events are also not treated as errors, but as warnings instead.

If this option is enabled these warnings are considered errors.

If no value, or the value ‘all’, is specified, the option applies to all of the keywords above. Alternatively, a comma separated list can be supplied with the keyword names it should apply to.

--disable-detection

Disable the detection engine.

--dump-config

Dump the configuration loaded from the configuration file to the terminal and exit.

--dump-features

Dump the features provided by Suricata modules and exit. Features list (a subset of) the configuration values and are intended to assist with comparing provided features with those required by one or more rules.

--build-info

Display the build information the Suricata was built with.

--list-app-layer-protos

List all supported application layer protocols.

--list-keywords=[all|csv|<kword>]

List all supported rule keywords.

--list-runmodes

List all supported run modes.

--set <key>=<value>

Set a configuration value. Useful for overriding basic configuration parameters. For example, to change the default log directory:

--set default-log-dir=/var/tmp

This option cannot be used to add new entries to a list in the configuration file, such as a new output. It can only be used to modify a value in a list that already exists.

For example, to disable the eve-log in the default configuration file:

--set outputs.1.eve-log.enabled=no

Also note that the index values may change as the suricata.yaml is updated.

See the output of --dump-config for existing values that could be modified with their index.

--engine-analysis

Print reports on analysis of different sections in the engine and exit. Please have a look at the conf parameter engine-analysis on what reports can be printed

--unix-socket=<file>

Use file as the Suricata unix control socket. Overrides the filename provided in the unix-command section of the configuration file.

--reject-dev=<device>

Use device to send out RST / ICMP error packets with the reject keyword.

--pcap-buffer-size=<size>

Set the size of the PCAP buffer (0 - 2147483647).

--netmap[=<device>]

Enable capture of packet using NETMAP on FreeBSD or Linux. If no device is supplied, the list of devices from the netmap section in the yaml is used.

--pfring[=<device>]

Enable PF_RING packet capture. If no device provided, the devices in the Suricata configuration will be used.

--pfring-cluster-id <id>

Set the PF_RING cluster ID.

--pfring-cluster-type <type>

Set the PF_RING cluster type (cluster_round_robin, cluster_flow).

-d <divert-port>

Run inline using IPFW divert mode.

--dag <device>

Enable packet capture off a DAG card. If capturing off a specific stream the stream can be select using a device name like “dag0:4”. This option may be provided multiple times read off multiple devices and/or streams.

--napatech

Enable packet capture using the Napatech Streams API.

--erf-in=<file>

Run in offline mode reading the specific ERF file (Endace extensible record format).

--simulate-ips

Simulate IPS mode when running in a non-IPS mode.

-u

Run the unit tests and exit. Requires that Suricata be configured with –enable-unittests.

-U, --unittest-filter=REGEX

With the -U option you can select which of the unit tests you want to run. This option uses REGEX. Example of use: suricata -u -U http

--list-unittests

Lists available unit tests.

--fatal-unittests

Enables fatal failure on a unit test error. Suricata will exit instead of continuing more tests.

--unittests-coverage

Display unit test coverage report.

/usr/local/etc/suricata/suricata.yaml

Default location of the Suricata configuration file.

/usr/local/var/log/suricata

Default Suricata log directory.

•

Suricata Home Page

•

Suricata Support Page