NAME

SYNOPSIS

DESCRIPTION

If the --phy=ID option is not given then --summary is assumed. When --summary is given or assumed, this utility shows the disposition of each active expander phy in table form. One row is shown for each phy and is described in the SINGLE LINE PER PHY FORMAT section below. For this purpose disabled expander phys and those with errors are considered "active" and can be suppressed from the output by adding the --brief option.

The DISCOVER LIST response may contain up to 8 descriptors when the "descriptor type" field in the request is set to 0 (e.g. --descriptor=0). The DISCOVER LIST response may contain up to 40 descriptors when the "descriptor type" field in the request is set to 1 (e.g. --descriptor=1). Multiple DISCOVER LIST requests will be made if more descriptors are requested (e.g. --summary requests 254) and the previous response indicates that more descriptors may be available.

Rather than supply options and SMP_DEVICE[,N] on every invocation some can be supplied via environment variables. See the section on ENVIRONMENT VARIABLES below.

OPTIONS

-A, --adn

causes the "attached device name" field to be output when the --one or --summary option is also given. See the section below on SINGLE LINE PER PHY FORMAT. Note the "attached device name" field is not available in the short format (e.g. --descriptor=1).

-b, --brief

reduce the decoded response output.

-c, --cap

decode and print phy capabilities bits fields (see SNW-3 in draft). Each expander phy has three of these fields: programmed, current and attached. By default these fields are only printed out in hex, or not at all if the --brief option is given or implied. Of the three the attached phy capability field is probably the most interesting. If the --verbose option is given, then the various "G" identifiers are expanded (e.g. instead of "G4:" it prints "G4 (12 Gbps):").

-d, --descriptor=TY

set the "descriptor type" field in the request. When TY is 0 then the 120 byte response defined by the DISCOVER function response (less its CRC field) is placed in the descriptors of this function's response. When TY is 1 the short format (i.e. 24 byte per descriptor) information is placed in the descriptors of this function's response.

-D, --dsn

outputs the device slot number at the end of each summary line. In summary mode one line is output per expander phy. It is output in the form "dsn=<val>" where <val> is decimal in the range from 0 to 254 inclusive. It is not output if it is not available or has the value 255. The device slot number is not available in short format, so with this option in summary mode, if the --descriptor=1 is not given, then the longer format is chosen. An expander typically contains a SES device which yields device slot numbers in its Additional Element Status diagnostic page.

-f, --filter=FI

set the filter field in the request. When FI is 0 (default) fetch descriptors for all phys. When FI is 1 only fetch descriptors for phys attached to (other) expanders. When FI is 2 only fetch descriptors for phys attached to expanders, SAS or SATA devices. When FI is 1 or 2, expander phys that would yield "phy vacant" (indicating they are hidden by zoning) are filtered out.

-h, --help

output the usage message then exit.

-H, --hex

output the response (less the CRC field) in hexadecimal.

-i, --ignore

sets the Ignore Zone Group bit in the SMP Discover list request.

-I, --interface=PARAMS

interface specific parameters. In this case "interface" refers to the path through the operating system to the SMP initiator. See the smp_utils man page for more information.

-n, --num=NUM

maximum number of descriptors fetch. If any descriptors are in the response the first phy id will be greater than or equal to the argument of --phy=ID. Note that maximum SMP frame size is 1032 bytes (including a trailing 4 byte CRC) which may limit the number of descriptors that can be fetched by a single DISCOVER LIST function (especially when '--descriptor=0').

-o, --one

use one line (summarized) format for each descriptor in the response. The default action when this option is not given is to output multiple indented lines for each descriptor in the response. See the section below on SINGLE LINE PER PHY FORMAT.

-p, --phy=ID

phy identifier. ID is a value between 0 and 254. This is the starting (lowest numbered) phy id to fetch in the response. Note that due to the filter field setting, the first phy id in the response may be greater than the argument to this option.

-r, --raw

send the response (less the CRC field) to stdout in binary. All error messages are sent to stderr.

-s, --sa=SAS_ADDR

specifies the SAS address of the SMP target device. Typically this is an expander. This option may not be needed if the SMP_DEVICE has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number in hexadecimal either prefix it with '0x' or put a trailing 'h' on it.

-S, --summary

output a multi line summary, with one line per active phy. Checks up to 254 phys starting at phy identifier ID (which defaults to 0). Equivalent to '-o -d 1 -n 254 -b' unless the --adn option was also given, in which case it is equivalent to '-o -d 0 -n 254 -b' . See the section below on SINGLE LINE PER PHY FORMAT.

-v, --verbose

increase the verbosity of the output. Can be used multiple times.

-V, --version

print the version string and then exit.

-Z, --zpi=FN

FN is a file that will be created or truncated then have zone phy information written to it in a format suitable for input to the smp_conf_zone_phy_info utility's --pconf=FN option. If --num=NUM is not given it is set to 254. The output will start from phy_id 0 unless --phy=ID is given.

SINGLE LINE PER PHY FORMAT

For each descriptor in the DISCOVER LIST response, one line is output starting with " phy <n>:" where <n> is the phy identifier (and they are origin zero). That is followed by the routing attribute represented by a single letter which is either "D" for direct routing, "S" for subtractive routing, "T" or "U". Both "T" and "U" imply table routing, the difference is that if REPORT GENERAL indicates "table to table supported" then "U" is output to indicate that phy can be part of an enclosure universal port; otherwise "T" is used. Next comes the negotiated physical link rate which is either "disabled", "reset problem" or "spinup hold". Other states are mapped to "attached". This includes enabled phys with nothing connected which appear as "attached:[0000000000000000:00]".

Information shown between the brackets is for the attached device. Phys that are connected display something like: "attached:[5000c50000520a2a:01 " where the first number is the attached SAS address (in hex) and the second number is the attached device's phy identifier. If the attached device type is other than an SAS or SATA device then one of these abbreviations is output: "exp" (for expander), "fex" (for fanout expander) or "res" (for unknown attached device type). If a phy is flagged as "virtual" then the letter "V" appears next. Next are the protocols supported by the attached device which are shown as "i(<list>)" for initiator protocols and/or "t(<list>)" for target protocols. The <list> is made up of "PORT_SEL", "SSP", "STP", "SMP" and "SATA" with "+" used as a separator. For example a SAS host adapter will most likely appear as: "i(SSP+STP+SMP)". This completes the information about the attached phy, hence the closing right bracket.

If appropriate, the negotiated physical link rate is shown in gigabits per second. Here is an example of a line for expander phy identifier 11 connected to a SATA target (or SATA "device" to use the t13.org term):

phy 11:T:attached:[500605b000000afb:00 t(SATA)] 1.5 Gbps

If the expander has zoning enabled (i.e. REPORT GENERAL response bit for 'zoning enabled' is set) and a phy's zone group is other than zg 1 then the phy's zone group is shown (e.g. "ZG:2").

If the --adn option is given then after the attached SAS address and the attached device's phy identifier are output an extra field is inserted containing the "attached device name" field. For a SAS disk this should be its target device name (in NAA-5 format) and for a SATA disk its WWN (if provided, also in NAA-5 format). Also when the --adn option is given the phy speed and zone group are not output in order to keep the line length reasonable.

If the --dsn option is given and device slot number information is available for the current phy, then "dsn=<num>" is appended to the line. Device slot numbers range from 0 to 254 with 255 meaning there is no corresponding slot so it is not listed.

ENVIRONMENT VARIABLES

If the SAS address (of the SMP target) is not given and it is required (i.e. it is not implicit in SMP_DEVICE[,N]) then the SMP_UTILS_SAS_ADDR environment variable is checked and if present its contents are used as the SAS address. SAS addresses are usually given in hex indicated by a leading '0x' or trailing 'h'.

A device slot number (dsn) is important for establishing the relationship between an expander phy and a SES array element. Newer expanders (e.g. SAS-3) support dsn_s in the DISCOVER (and DISCOVER LIST) functions. These can be shown, if available, with the --dsn option to smp_discover and smp_discover_list utilities.. To ease typing that option often, the SMP_UTILS_DSN environment variableriable, if present, has the same effect.

NOTES

CONFORMING TO

AUTHORS

REPORTING BUGS

COPYRIGHT

SEE ALSO