NAME

SYNOPSIS

DESCRIPTION

-a

Dump the currently existing NDP entries. The following information will be printed:

Neighbor

IPv6 address of the neighbor.

Linklayer Address

Linklayer address of the neighbor. It could be “(incomplete)” when the address is not available.

Netif

Network interface associated with the neighbor cache entry.

Expire

The time until expiry of the entry. The entry could become “permanent”, in which case it will never expire.

S

State of the neighbor cache entry, as a single letter:

N

Nostate

W

Waitdelete

I

Incomplete

R

Reachable

S

Stale

D

Delay

P

Probe

?

Unknown state (should never happen).

Flags

Flags on the neighbor cache entry, in a single letter. They are: Router, proxy neighbor advertisement (“p”). The field could be followed by a decimal number, which means the number of NS probes the node has sent during the current state.

-A wait

Repeat -a (dump NDP entries) every wait seconds.

-c

Erase all the NDP entries.

-d

Delete specified NDP entry.

-f filename

Cause the file filename to be read and multiple entries to be set in the NDP table. Entries in the file should be of the form

hostname ether_addr [temp] [proxy]

with argument meanings as given above. Leading whitespace and empty lines are ignored. A ‘#’ character will mark the rest of the line as a comment.

-H

Harmonize consistency between the routing table and the default router list; install the top entry of the list into the kernel routing table.

-I

Shows the default interface used as the default route when there is no default router.

-I interface

Specifies the default interface used as the default route when there is no default router. The interface will be used as the default.

-I delete

The current default interface will be deleted from the kernel.

-i interface [expressions ...]

View ND information for the specified interface. If additional arguments expressions are given, ndp sets or clears the flags or variables for the interface as specified in the expression. Each expression should be separated by white spaces or tab characters. Possible expressions are as follows. Some of the expressions can begin with the special character ‘-’, which means the flag specified in the expression should be cleared. Note that you need -- before -foo in this case.

nud

Turn on or off NUD (Neighbor Unreachability Detection) on the interface. NUD is usually turned on by default.

accept_rtadv

Specify whether or not to accept Router Advertisement messages received on the interface. This flag is set by net.inet6.ip6.accept_rtadv sysctl variable.

auto_linklocal

Specify whether or not to perform automatic link-local address configuration on interface. This flag is set by net.inet6.ip6.auto_linklocal sysctl variable.

no_prefer_iface

The address on the outgoing interface is preferred by source addess selection rule. If this flag is set, stop treating the address on the interface as special even when the interface is outgoing interface. The default value of this flag is off.

disabled

Disable IPv6 operation on the interface. When disabled, the interface discards any IPv6 packets received on or being sent to the interface. In the sending case, an error of ENETDOWN will be returned to the application. This flag is typically set automatically in the kernel as a result of a certain failure of Duplicate Address Detection. If the auto_linklocal per-interface flag is set, automatic link-local address configuration is performed again when this flag is cleared.

basereachable=(number)

Specify the BaseReachbleTimer on the interface in millisecond.

retrans=(number)

Specify the RetransTimer on the interface in millisecond.

curhlim=(number)

Specify the Cur Hop Limit on the interface.

-n

Do not try to resolve numeric addresses to hostnames.

-p

Show prefix list. The following information will be printed:

if

The network interface associated with this prefix.

flags

The status of the prefix, expressed by a combination of the following letters:

A

This prefix can be used for stateless address autoconfiguration.

L, O

This prefix can be used for on-link determination; that is, it can be used to determine whether a given destination address is on-link.

D

There are no reachable routers advertising this prefix.

vltime

Valid lifetime; the length of time for which the prefix and a stateless autoconfigured address generated from this prefix can be used for the source or destination address of a packet.

pltime

Preferred lifetime; the length of time for which the prefix and a stateless autoconfigured address generated from this prefix can be used by upper-layer protocols unrestrictedly.

expire

This is the remaining time that the prefix is in the valid state.

ref

The number of kernel references held for this prefix.

-P

Flush all the entries in the prefix list.

-r

Show default router list.

-R

Flush all the entries in the default router list.

-s

Register an NDP entry for a node. The entry will be permanent unless the word temp is given in the command. If the word proxy is given, this system will act as a proxy NDP server, responding to requests for hostname even though the host address is not its own.

-t

Print timestamp for each entry, to make it possible to merge the output with tcpdump(1). Most useful when used with -A.

EXIT STATUS

SEE ALSO

HISTORY